Super Therm® Uses and Applications

Perfect For: Factories, Warehouses, Government buildings, Councils, Homes, Roofs, Sheds, Pergolas, Rollerdoors, RVs, Motorhomes, Caravans, Brickwork, Shipping Containers, Trucking, Air-conditioning ducts, External Walls and more.

As Super Therm® is the a leading barrier to heat penetration is also means it blocks up to 95% SOLAR HEAT from entering a structure or any other substrate caused by Visual Light, Ultra Violet (UV) & Infrared (IR). This leaves only ambient heat and not radiant heat.

Application conditions

VOC-Compliant: Only 67 grams/litre. Limit in Australia is Latex roof paint is 100 (CSIRO)
USDA-Approved: For use in and around food preparation facilities
Mildew and mould: Can withstand moisture
Fire tested: “0” flame and smoke results. No off gassing (NASA)
Spread: 100 sq.ft./gallon on roofing and walls.
New galvanized metal/slick metal surfaces, stainless steel and aluminum — apply Rust Grip at 300 sq.ft./ gallon as a primer first, then Super Therm® at 100 sq.ft./ gallon (if rusted areas, Rust Grip at 200 sq.ft./ gallon as primer)
Weathered metal surfaces: (5-10 years old), no primer needed Apply Super Therm® at 100 sq.ft./gallon (if no rust is present).
Concrete surfaces: If painted before, just make sure all loose or flaking paint is off first, then apply Super Therm® directly. If not painted before, seal concrete first using Super Base (HS) at 100 sq.ft./gallon, then apply Super Therm® .
Tar/Asphalt or Rubber Surfaces: Seal first with Super Base (HS) at 30 sq.ft./gallon, then apply Super Therm® . Tar and asphalt will bleed oil residues into the coating, turning it brown and interfering with the heat block ability of Super Therm® if not sealed first. Super Base (HS) is water-based and, therefore, will not soften or harm the tar/asphalt but will completely fill and seal all holes, cracks and broken seams.
Flat Roof Systems: Remove all loose gravel and power. wash. Watch for roofs with consistent leaking; if present, push for roofing system #1 or #2.

System #1–Apply Super Base (HS) at 30 sq.ft./gallon As you apply Super Base (HS), lay in the polyester membrane (36″ width x 360′ length) as you go. Let dry and re-apply Super Base (HS) over the membrane at 100 sq.ft./gallon. Let dry, then apply Super Therm® at 100 sq.ft./gallon for the coating; and last apply SP Clear Protector at 250 sq.ft/gallon as a top coat. Total mil thickness will be: Super Base (HS) -21 mils, mesh-6 mils, SUPER BASE (HS 7 mils, Super Therm® – 7 mils, SP Clear Protector-2 mils 43 mills.

System #2 (solid roof, absolutely no leaks)–Apply Super Base (HS) at 30 sq.ft./gallon Apply Super Therm® at 100 sq.ft./gallon. Apply SP Clear Protector at 250 sq.ft./gallon. Total mil thickness: 30 mils

Walls (interior/exterior): Apply Super Therm® at 2.2 litres per m2.
Tinting: Can tint to any earth-tone colours. Not medium to dark tones. Never tint to grey – the black tint will cover the ceramic particles first and block their effectiveness. Best approach is to apply Super Therm® in 2 coats, let dry, then paint a coloured paint over the Super Therm® as your finishing coat.
Acid/Salt-resistance: Will withstand mild acids and salt spray.
High humidity: After Super Therm® dries completely, no effect on coating.
UV/Weathering: Very UV-stable, will withstand basic weathering for 2025 years minimum
“R” Factoring: Super Therm® does not an R rating because it is an ceramic heat block coating. It has a 99BTU rating. Blocks 99% of Infra red heat.
Application: Always power wash substrate using a minimum of 3000 psi power washer to clean dirt, oils, etc. Use washing powders in washing systems and rinse well.

Looking to join one of the world’s leading coatings companies. Contact us if you’re a quality applicator looking for new products and markets!